IEC 60601-2-52 Related Medical Bed Test Tools and Fixtures

Standards and Test Method Support

These Medical Bed Test Tools and Fixtures are intended for IEC 60601-2-52 related medical bed safety testing and are manufactured according to the corresponding GB / YY 9706.252 figures and clauses.

The tools support selected medical bed mechanical safety evaluations, including:

• Entrapment-related evaluation
• Gap and opening assessment
• Loading pad application
• Pressure plate loading
• Footboard force application
• Medical bed mechanical safety verification
• Hospital bed and nursing bed test program setup

Because IEC, GB and YY editions may differ in clause numbering, figure references or national adoption details, customers should confirm the applicable standard version and test clause before final tool selection.

Key Tool Set Overview

How These Medical Bed Test Tools Support the Test Program

Medical bed safety testing often requires more than one individual fixture. Different test tools are used to reproduce specific contact, loading, gap-checking or force-application conditions during IEC60601-2-52 related medical bed evaluation.

This tool set helps laboratories build a more complete medical bed mechanical safety test workflow. The cone tool and cylindrical tool are mainly used for entrapment and gap-related assessment. The loading pad and pressure plate support defined load application to bed structures and support surfaces. The footboard force application device is used when a controlled force needs to be applied to the footboard area.

By selecting the correct tool according to the applicable GB / YY 9706.252 figure or clause, manufacturers and laboratories can reduce tool mismatch, improve test repeatability and prepare more clearly for product development verification, internal quality control or third-party test preparation.

Tool Selection Guide

This table is intended as a general tool selection reference. Final tool selection should be confirmed according to the applicable standard edition, test clause, medical bed design and laboratory test procedure.

Tool Details

KP-61521 Cone Tool — IEC 60601-2-52 Figure 201.103a

The KP-61521 Cone Tool, also referred to as an entrapment test tool, is manufactured according to IEC 60601-2-52-2021 Figure 201.103a. It is used for medical bed entrapment-related evaluation and helps laboratories check whether openings, gaps or accessible areas may create entrapment risks during use.

The tool is manufactured with defined weight, surface roughness and dimensions to support repeatable application during medical bed safety assessment.

KP-61522 Cylindrical Tool — IEC 60601-2-52 Figure 201.103b

The KP-61522 Cylindrical Tool is manufactured according to IEC 60601-2-52-2021 Figure 201.103b. It is used together with other medical bed test tools for gap, opening and entrapment-related evaluation.

The stainless steel construction, defined weight and controlled surface roughness help maintain consistent contact conditions during medical bed safety testing.

KP-61523 Loading Pad — IEC 60601-2-52 Figure 201.104

The KP-61523 Loading Pad is manufactured according to IEC 60601-2-52-2021 Figure 201.104. It is used to apply standardized loading conditions during medical bed mechanical safety evaluation.

The loading pad assembly includes the loading pad, stainless steel cylinder and loading steel balls. This configuration provides a controlled method for applying load to medical bed structures and support surfaces.

KP-61525 Pressure Plate — IEC 60601-2-52 Figure 201.112 / Clause 201.9.4.2.2

The KP-61525 Pressure Plate is manufactured for pressure and loading evaluation according to IEC 60601-2-52-2021 Figure 201.112 and Clause 201.9.4.2.2. It is used to apply controlled load to specified areas of medical bed structures.

The pressure plate is made of stainless steel and can be configured with loading steel balls to achieve an adjustable total load range from 100 N to 2200 N.

KP-61526 Footboard Force Application Device — IEC 60601-2-52 Clause 201.15.4.7.1

The KP-61526 Footboard Force Application Device is designed for footboard force application testing according to IEC 60601-2-52 Clause 201.15.4.7.1. It applies a defined force to the footboard area of a medical bed to support mechanical strength and safety evaluation.

The device uses pneumatic actuation, with test time adjustable from 0 to 9999 seconds according to the selected test procedure.

Complete Specifications Summary

Typical Test Workflow

The following workflow shows how these tools are typically used in a medical bed safety test program. Actual steps may vary according to the selected standard clause and laboratory procedure.

1. Confirm the applicable standard version, figure or clause.
2. Identify the required test item, such as entrapment evaluation, loading application or footboard force testing.
3. Select the corresponding tool model from the tool set.
4. Confirm tool weight, dimensions, material and surface condition before testing.
5. Position the tool according to the medical bed structure and test requirement.
6. Apply the required load, contact or force according to the selected procedure.
7. Record the test condition, tool used, bed position and observed result.
8. Inspect the bed structure, opening, support surface or footboard area after testing.

Testing Purpose and Application

The Medical Bed Test Tools and Fixtures support repeatable mechanical safety evaluation for medical beds and related care bed products. They help laboratories apply defined contact, loading and force conditions during medical bed test programs.

Typical applications include:

• Entrapment risk evaluation
• Gap and opening assessment
• Loading application for bed support structures
• Pressure loading on specified areas
• Footboard force application
• Mechanical safety verification for medical beds
• Quality control for hospital bed and nursing bed manufacturers

These tools are suitable for medical bed manufacturers, third-party laboratories, R&D teams and quality control departments that need standard-related fixtures for medical bed safety testing.

Tool Kit Configuration Options

KingPo can supply these Medical Bed Test Tools and Fixtures individually or as a configured tool set. Customers may select only the required tools for a specific test item, or request a more complete set for medical bed development, laboratory setup or quality control programs.

A complete configuration may include the KP-61521 Cone Tool, KP-61522 Cylindrical Tool, KP-61523 Loading Pad, KP-61525 Pressure Plate and KP-61526 Footboard Force Application Device. Tool configuration can be reviewed according to the customer’s test items, applicable standard version and medical bed structure.

For laboratories building a new medical bed test capability, it is recommended to confirm the full list of required test tools together with the related medical bed test systems, fixtures and documentation requirements.

Material, Weight and Verification Notes

Medical bed test tools must maintain correct dimensions, weight, material configuration and surface condition to support repeatable test results. Before use, the tool weight, key dimensions and surface condition should be confirmed according to the selected test method and laboratory procedure.

For projects requiring documented traceability, weight verification, dimensional confirmation or inspection support can be discussed according to customer requirements and local laboratory practices.

If the tools are used in a regulated laboratory or third-party testing environment, the required documentation format should be confirmed before ordering.